BMW · NHTSA safety record

2012 BMW 128I

Every safety complaint, recall and defect investigation the US government holds on this vehicle.

Owners have filed 31 safety complaints about the 2012 BMW 128I with the US government. Of those, 2 describe a crash, 1 person was injured and no death is recorded. 5 recall campaigns are open against it.

The most complained-about system is the air bags, named in 23 complaints, 74% of the total. The typical failure was reported at 30,500 miles, the median across the 6 complaints that gave an odometer reading.

Compiled from NHTSA's complaint, recall and investigation files · Covers November 2013 to August 2026 · How this is counted

What is on file

31 complaints on file

Complaints

Describe a crash

Mention fire

People injured

Deaths

A complaint is an unverified account by the person who filed it, not a finding of fault. One complaint is one ODI number, which is how NHTSA counts them.

A recall is the manufacturer conceding a defect, and the repair is free. Whether one covers your particular car is a question only its VIN can answer, because a campaign covers a production range rather than a model year. A further 1 defect investigation is open and unresolved.

Which system owners named

Complaints naming each system

AIR BAGS 23 · 74% 23 74%

ENGINE 4 · 13% 4 13%

ENGINE AND ENGINE COOLING 2 · 6% 2 6%

FUEL/PROPULSION SYSTEM 2 · 6% 2 6%

ELECTRICAL SYSTEM 1 · 3% 1 3%

SEAT BELTS 1 · 3% 1 3%

SERVICE BRAKES 1 · 3% 1 3%

UNKNOWN OR OTHER 1 · 3% 1 3%

VEHICLE SPEED CONTROL 1 · 3% 1 3%

0 12 23

Red marks a system with a recall campaign against it. One complaint can name several systems, so these add up to more than 31.

When the complaints arrived

By the year NHTSA received them

By the year NHTSA received them, which is not the year the failures happened. They peaked in 2017 at 14.

16 12 8 4

13 2013 16 2016 17 2017 18 2018 22 2022 24 2024 26 2026

This is the year the complaint was filed, not the year the failure happened. The range runs from 2013 to 2026, the last of them a part year, which is why its column is drawn faint.

Crash test ratings

NHTSA New Car Assessment Program

NHTSA has not crash tested the 2012 BMW 128I. Its New Car Assessment Program tests a selection of each year's vehicles and does not reach motorcycles, heavy trucks, motorhomes or most low-volume models, so an absence here says nothing about how the vehicle would perform. It is not a low score.

What owners have reported about this vehicle is below, and it is a different question: a crash test measures what happens to the people inside in a controlled impact, while a complaint records what broke during ordinary use.

Recall campaigns

5 on file

ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)

22V119000 · March 2, 2022

The defect: BMW of North America, LLC (BMW) is recalling certain 2008-2013 1 Series Coupe (128i); 2007-2013 3 Series Coupe (328i, 328xi, 328i xDrive); 2007-2010 X3 SAV (X3 3.0si, X3 xDrive30i); 2008-2013 1 Series Convertible (128i); 2006-2011 3 Series Sedan (325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi); 2006-2012 3 Series Wagon (328i, 328i xDrive); 2007-2013 3 Series Convertible (328i); 2006-2010 5 Series Sedan (525i, 525xi, 528i, 528xi, 530i, 530xi); 2006-2007 5 Series Wagon (530xi); 2007-2010 X5 SAV (X5 3.0si, X5 xDrive30i); 2006-2008 Z4 Coupe (Z4 3.0si); and 2006-2011 Z4 Roadster (Z4 3.0i, Z4 3.0si, Z4 sDrive30i) vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.
The risk: An electrical short can cause the PCV valve heater to overheat, increasing the risk of a fire while driving or, soon after driving when parked.
The remedy: This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Dealers will install an electrical wiring harness with fuse protection for the PCV Valve heater in potentially affected vehicles, free of charge. This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Vehicles previously repaired under the prior recalls will need to come back for the new recall remedy. The remedy is currently being developed. Interim owner notification letters informing owners of the safety risk were mailed on April 1, 2022. Owner notification letters were mailed on July 22, 2022. Owners may contact BMW customer service at 1-800-525-7417.

BMW of North America, LLC · up to 917,106 vehicles across all model years covered

AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE

20V017000 · January 15, 2020

The defect: BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
The risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
The remedy: BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.

BMW of North America, LLC · up to 59,965 vehicles across all model years covered

ELECTRICAL SYSTEM:WIRING

19V579000 · August 6, 2019

The defect: BMW of North America, LLC (BMW) is recalling certain 2008-2012 BMW 128i, 135i, 135is Coupes and 128i, 135i Convertible vehicles. The wiring and electrical connectors in the blower-regulator wiring harness may overheat.
The risk: Wiring that overheats could cause the electrical connectors to melt, and increase the risk of a fire, even when the vehicle is unattended.
The remedy: BMW will notify owners, and dealers will inspect the blower-regulator wiring harness, and replace it with a new part, free of charge. The recall began October 4, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of an earlier recall number 17V-676.

BMW of North America, LLC · up to 41,981 vehicles across all model years covered

AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE

16V071000 · February 5, 2016

The defect: BMW of North America, LLC (BMW) is recalling certain model year 2008-2013 128i and 135i coupes and convertibles and 1 Series M coupes, 2006-2011 325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi, 335i, 335xi, 335i xDrive Sedans, 2009-2011 335d sedans, 2006-2012 325xiT, 328i and 328xi sports wagons, 2007-2013 328i, 328xi, 328i xDrive, 335i, 335xi, 335i xDrive, 335is and M3 Coupes and Convertibles, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i SAVs, 2007-2010 X3 xDrive30i SAVs, 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M SAVs, 2009-2013 BMW X5 xDrive35d SAVs, 2008-2014 X6 xDrive35i, X6 xDrive50i, and X6 M SACs, 2010-2011 BMW X6 xDrive50i SACs and 2008-2011 M3 Sedan vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.
The risk: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
The remedy: BMW will notify owners, and dealers will replace the driver's frontal air bag module or inflator depending on the vehicle model, free of charge. The recall began March 9, 2018. Owners may contact BMW customer service at 1-800-525-7417.

BMW of North America, LLC · up to 840,000 vehicles across all model years covered

ELECTRICAL SYSTEM

13V044000 · February 7, 2013

The defect: BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
The risk: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
The remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at [email protected].

BMW of North America, LLC · up to 516,791 vehicles across all model years covered

Defect investigations

1 on file

An investigation means NHTSA has decided a pattern is worth examining. A preliminary evaluation is often closed with no action; an engineering analysis is the stage that usually precedes a recall.

Desiccated Air Bag Inflator Rupture

EA21002

Still open engineering analysis · opened September 17, 2021

the air bags

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

In owners’ own words

Quoted from the complaint file

Quoted from NHTSA's complaint file. These are unverified accounts by the people who filed them, not findings of fault.

AIR BAGS Filed October 17, 2017

1 injured · crash · towed · 50,000 miles

TL* THE CONTACT OWNED A 2012 BMW 128I. WHILE DRIVING APPROXIMATELY 30 MPH AND MAKING A LEFT TURN INTO TRAFFIC, THE CONTACT CRASHED INTO ANOTHER VEHICLE. THE AIR BAGS DEPLOYED. AS A RESULT, METAL FRAGMENTS STRUCK THE CONTACT'S FACE AND CHEST THAT REQUIRED MEDICAL ATTENTION. A POLICE REPORT WAS FILED. THE VEHICLE WAS TOWED TO A LOCAL TOWING COMPANY. THE VEHICLE WAS NOT TAKEN TO A DEALER. THE VEHICLE WAS DESTROYED. THE VIN WAS INCLUDED IN NHTSA CAMPAIGN NUMBER: 16V071000 (AIR BAGS). THE MANUFACTURER WAS NOT CONTACTED. THE APPROXIMATE FAILURE MILEAGE WAS 50,000.

NHTSA complaint 11034045. Filed by an owner and not verified by NHTSA or by us.

VEHICLE SPEED CONTROL Filed November 27, 2013

crash · 9,500 miles

PULLING IN PARKING LOT TO PARK GOING AT A VERY LOW SPEED I HIT THE BRAKES AND THEY DID NOT HOLD INSTEAD THE CAR ACCELERATED AND JUMPED ON TO A SIDEWALK AND THEN INTO A BRICK WALL. I FINALLY WAS ABLE TO GET THE CAR IN REVERSE AND IT TOOK OFF BACKWARDS FOR A FEW FEET UNTIL THE BRAKES FINALLY CAUGHT THE CAR THEN CAME TO A SUDDEN STOP. I HIT THE BRICK WALL WITH THE FRONT END OF MY CAR CAUSING LOTS OF DAMAGE TO THE FRONT OF MY CAR AND THE BUILDING THE AIR BAG NEVER DEPLOYED. THE POLICEMAN THAT WORKED THE WRECK SAID THE TIRE MARKS WHERE THE CAR TOOK OFF WERE ACCELERATION MARKS NOT BRAKE MARKS, BUT THE ONES WHERE IT FINALLY STOPPED WERE BRAKE MARKS. *TR

NHTSA complaint 10554034. Filed by an owner and not verified by NHTSA or by us.

SEAT BELTS Filed August 24, 2026

My mother was in the passenger seat and the seat belt buckle would not allow the tongue to be inserted. After several attempts we got it in but when we got home I tried to engage the seat belt several times, I tried to lubricate the buckle no luck... I ordered a new buckle. The BMW dealer said there had been no other complaints and it was not under recall. As soon as I get the new part I will retain the buckle if needed.

NHTSA complaint 11759010. Filed by an owner and not verified by NHTSA or by us.

ENGINE Filed May 19, 2026

Prior to August 2024, this vehicle operated with zero check engine lights or drivetrain faults. In August 2024, BMW of Pittsburgh executed federally mandated Safety Recall 23V-707, which required opening the cylinder head. Immediately following this service, the Check Engine Light began illuminating persistently.On or about October 3, 2024, an independent diagnostic scan at Bobby Rahal BMW pulled BMW Factory Code 002A89: Exhaust VANOS Camshaft Mechanism Fault (Mechanical Sticking/Flow Restriction). Technicians at Bobby Rahal BMW explicitly instructed me to return the car to BMW of Pittsburgh because they suspected the original VANOS safety recall repair was botched.On October 28, 2024, I

NHTSA complaint 11738803, quoted in part. Filed by an owner and not verified by NHTSA or by us.

ENGINE Filed March 24, 2026

Due to BMW using plastic parts when you live in Hot and cold environments the plastic begins to mold to other plastic parts and pvc diaphragms tear rather easy causing rough idle , stalls and can cause over revving and send a car into another car while in gear. The cheap plastic cause oil leaks and when oil gets low cause engine failure as well.

NHTSA complaint 11726596. Filed by an owner and not verified by NHTSA or by us.

ENGINE Filed March 6, 2026

On February 25, 2026, BMW of South Miami performed the VANOS safety recall repair on my vehicle. The repair order documented that VANOS bolts were missing and retrieved from the engine oil pan and that VANOS components were serviced. Within approximately 24–48 hours of picking up the vehicle, the check engine light illuminated and the vehicle began operating abnormally, including rough idle and irregular shifting. The vehicle stored diagnostic fault code P054B (camshaft position timing over-retarded), which directly relates to camshaft timing and the VANOS system involved in the recall repair. I returned the vehicle to the dealership for further diagnosis. The dealership stated an

NHTSA complaint 11722577, quoted in part. Filed by an owner and not verified by NHTSA or by us.

ENGINE AND ENGINE COOLING Filed July 9, 2024

The contact owns a 2012 BMW 128I. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue and confirmed that parts were not yet available. The contact had not experienced a failure. VIN tool confirms parts not available.

NHTSA complaint 11600565. Filed by an owner and not verified by NHTSA or by us.

ENGINE Filed June 16, 2022

79,769 miles

The contact owns a 2012 BMW 128i. The contact stated after completing an oil change at the dealer and starting the vehicle, the RPM started fluctuating. The contact stated that after coming to a complete stop at a traffic light, the RPM fluctuated rapidly and the vehicle decelerated while driving. The dealer was notified of the failure and advised the contact to take the vehicle back to the dealer for a diagnostic test. The contact was able to drive to the dealer at a slower speed. The dealer diagnosed that the VANOS (Variable Nockenwell Steuerung) system needed to be replaced. The dealer informed the contact that the failure was a manufacturing defect; however, she would be responsible for

NHTSA complaint 11469556, quoted in part. Filed by an owner and not verified by NHTSA or by us.

Compare

Other years of the BMW 128I

Model year	Complaints	Recalls	Deaths
2013	36	3	—
2011	50	7	—
2010	22	7	—

Other 2012 BMW models

X5 271 328I 130 528I 90 528XI 54 535I 54 X3 42 550I 35 K 1600 GTL 33

Complaints on file, same model year.

Every BMW on this site — 257 vehicles.

If this is your car and a dealer keeps failing to fix it, your state's lemon law may require the manufacturer to replace it or buy it back. How many repair attempts it takes, and how long you have to file, is set by the state you bought in and by nothing on this page.

Where these numbers come from

Complaints: NHTSA's ODI complaint file, published October 2, 2026. One complaint is one ODI number, which is how NHTSA counts them.
Recalls: NHTSA's recall campaign API, newest campaign on this vehicle filed March 2, 2022.
Investigations: NHTSA's ODI investigation file, published October 2, 2026.

A complaint is one owner's account and has not been verified by NHTSA or by us. A vehicle with more complaints is not necessarily worse: models that sold in larger numbers collect more of them. How this is counted.

Compiled and maintained by guarledes
Independent developer and analyst