2010 Jeep Wrangler

The defect

Chrysler (FCA US LLC) is recalling certain model year 2007-2010 Jeep Wrangler JK vehicles manufactured March 2, 2006, to August 13, 2010. The clockspring assembly may become contaminated with dust and cause the air bag circuit to fail.

The risk

Failure of the air bag circuit may prevent the driver's frontal air bag from deploying in the event of a crash, increasing the risk of injury.

The remedy

Chrysler will notify owners, and dealers will replace the clockspring, wheel back cover, and column shroud, free of charge. The recall began on December 14, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S33.

Chrysler (FCA US LLC) · up to 388,532 vehicles across all model years covered

The defect

Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 Jeep Wrangler right-hand drive vehicles manufactured February 1, 2007, through October 10, 2011. The affected vehicles have airbag clockspring assemblies that could experience broken airbag circuits.

The risk

In the event of a crash necessitating airbag deployment, a broken electrical circuit in the airbag clockspring wiring assembly can lead to non-deployment of the driver-side frontal airbag and will not be able to properly protect the driver, increasing the risk of injuries.

The remedy

Chrysler will notify owners, and dealers will replace the clockspring and add a steering wheel dust shield, free of charge. The recall began on June 10, 2013. Owners may contact Chrysler at 1-800-247-9753. This recall supercedes NHTSA recall 11V-528. Chrysler's recall campaign number is M31.

Chrysler Group LLC · up to 5,440 vehicles across all model years covered

The defect

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2010 JEEP WRANGLER VEHICLES EQUIPPED WITH AN AUTOMATIC TRANSMISSION. THE TRANSMISSION SKID PLATE, WHICH IS CLOSE TO THE CATALYTIC CONVERTER, CAN COLLECT DEBRIS.

The risk

IF THIS OCCURS, THE DEBRIS CAN IGNITE WITHOUT WARNING, RESULTING IN A VEHICLE FIRE.

The remedy

CHRYSLER WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE SKID PLATE WITH A SKID BAR, FREE OF CHARGE. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

CHRYSLER GROUP LLC · up to 65,246 vehicles across all model years covered

The defect

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2008-2012 RIGHT HAND DRIVE (RHD) JEEP WRANGLER VEHICLES MANUFACTURED FROM FEBRUARY 1, 2007, THROUGH OCTOBER 10, 2011. SOME VEHICLES MAY BE EQUIPPED WITH DRIVER'S AIRBAG CLOCKSPRING ASSEMBLIES THAT COULD EXPERIENCE A COMPROMISED AIRBAG CIRCUIT RESULTING IN AN AIRBAG LAMP ILLUMINATION, WHICH INDICATES THAT THE AIRBAG MAY NOT DEPLOY.

The risk

A BROKEN ELECTRICAL CIRCUIT IN THE AIRBAG CLOCKSPRING WIRING ASSEMBLY CAN LEAD TO NON-DEPLOYMENT OF THE DRIVER FRONTAL AIRBAG AND WILL NOT BE ABLE TO PROPERLY PROTECT THE DRIVER IN THE EVENT OF A CRASH, INCREASING THE RISK OF INJURIES.

The remedy

CHRYSLER WILL NOTIFY OWNERS AND REMEDY THE VEHICLES AS NECESSARY FREE OF CHARGE. CHRYSLER WILL MAIL TO OWNERS AN INTERIM NOTIFICATION DURING MARCH 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

CHRYSLER GROUP LLC · up to 5,437 vehicles across all model years covered

The defect

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2010-2011 JEEP WRANGLER VEHICLES MANUFACTURED FROM JULY 12, 2010, THROUGH SEPTEMBER 10, 2010. SOME VEHICLES MAY EXPERIENCE A DEGRADATION OF FASTENER TORQUE FOR VARIOUS FRONT AND REAR AXLE ATTACHMENTS TO THE CHASSIS MODULE.

The risk

THIS COULD RESULT IN NOISE, OR ULTIMATELY, DEGRADATION IN STEERING AND HANDLING CHARACTERISTICS WHICH COULD LEAD TO LOSS OF DIRECTIONAL CONTROL OF THE VEHICLE INCREASING THE RISK OF A CRASH.

The remedy

DEALERS WILL RE-TORQUE ALL NINETEEN FASTENERS TO THE MAXIMUM RESIDUAL TORQUE VALUES. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 24, 2011. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

CHRYSLER GROUP LLC · up to 18,326 vehicles across all model years covered

The defect

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2010 LEFT HAND DRIVE JEEP LIBERTY, DODGE NITRO AND RAM 1500 TRUCK; RIGHT AND LEFT HAND DRIVE JEEP WRANGLER VEHICLES. THESE VEHICLES MAY HAVE BEEN BUILT WITH AN IMPROPERLY FORMED MASTER CYLINDER TO HYDRAULIC CONTROL UNIT (HCU) BRAKE TUBE ASSEMBLY END FLARE.

The risk

THIS COULD LEAD TO LOSS OF BRAKE FLUID AND REDUCED BRAKING PERFORMANCE INCREASING THE RISK OF A CRASH.

The remedy

DEALERS WILL REPLACE THE BRAKE TUBES FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING AUGUST 2010. OWNERS MAY CONTACT CHRYSLER TOLL-FREE AT 1-800-853-1403.

CHRYSLER GROUP LLC · up to 20,626 vehicles across all model years covered

The defect

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2007 THROUGH 2010 JEEP WRANGLER LEFT AND RIGHT HAND DRIVE PASSENGER VEHICLES MANUFACTURED FROM MAY 15, 2006 THROUGH APRIL 22, 2010. THERE MAY BE CONTACT BETWEEN THE RIGHT AND LEFT FRONT INNER FENDER LINERS AND THE RIGHT FRONT AND LEFT REAR BRAKE TUBES WHICH COULD CAUSE WEAR OF THE TUBES CAUSING A BRAKE FLUID LEAK.

The risk

A BRAKE FLUID LEAK CAN CAUSE PARTIAL LOSS OF SERVICE BRAKES AT THE AFFECTED WHEEL INCREASING THE RISK OF A CRASH.

The remedy

CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. OWNERS MAY CONTACT CHRYSLER TOLL-FREE AT 1-800-853-1403.

CHRYSLER GROUP LLC · up to 287,653 vehicles across all model years covered

Still open engineering analysis · opened September 17, 2021

the air bags

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Closed engineering analysis · opened April 19, 2019 · closed September 19, 2024 · led to recall 20V024

the air bags

The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect.  During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW.  The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications.  The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU.  In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment.  FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle.  Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW.  These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes.  An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time.   In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU.  This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners.  Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW.  The risk associated with the ASIC is equally shared among all OEMS involved in the investigation.  The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage.  There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation.  The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU.  If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC.  Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC.  All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled.  In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024.  With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.

Closed engineering analysis · opened December 4, 2015 · closed July 6, 2016 · led to recall 16V288000

the air bags

On May 10, 2016, Fiat Chrysler America (FCA) submitted a Part 573 Defect Information Report announcing NHTSA recall 16V290 involving 394,258 model year (MY) 2007-2010 Jeep Wrangler vehicles.Under the recall FCA will replace the clockspring and install a steering wheel back cover and steering wheel column shroud.This recall also includes approx. 4,524 MY2007-2010 right hand drive (RHD) Jeep Wrangler vehicles commonly used for rural postal delivery services.In addition 7,180 MY 2011-2016 right hand drive Jeep Wrangler vehicles were also recalled under 16V288, the same remedy repair will be used.Upon review of the 1,942 MY 2007-2010 Jeep Wrangler consumer complaints, 17,195 warranty reports and field returned parts assessment, FCA concluded that a defect exists in the driver side clockspring assembly, a device that both connects (electrically) the driver air bag to the control module and allows rotational movement between the steering wheel and fixed steering column.Clockspring failure may compromise the air bag circuit causing illumination of the air bag warning lamp, and may result in non-deployment of the driver air bag in a frontal crash.FCA identified a contributing factor in that the recalled vehicles may be subjected to off-road dusty environments and/or usage with the vehicle roof top/doors removed thus allowing dust and moisture to enter the clockspring assembly.FCA advised that the MY 2011 and later Wrangler vehicles had an improved steering column cover/shroud that may reduce the amount of dirt/moisture that can enter the clockspring assembly.During the investigation FCA and the Office of Defects Investigation (ODI) also reviewed 193 MY 2011-2012 Jeep Wrangler consumer complaints, 3,918 warranty reports and field returned parts along with reports from other FCA vehicles that use the same clockspring assembly.Based on this review, the rate of repair and the failure mode does not indicate a defect trend at this time in the later MY Wrangler or other FCA vehicles.During the field return parts review, FCA found a significant number of MY 2011-2012 Wrangler returned parts that operated normally, the so called ?no trouble found? or NTF parts where no fault could be identified through bench testing.On June 10, 2016, FCA informed ODI of its intention to conduct a 15-yr, 150k mile extended warranty program due to the NTF issue and the MY 2011 and later vehicles having a somewhat elevated level of warranty replacement.Consumers will be notified of the program in writing.FCA will collect clocksprings replaced under the warranty extension program to further examine and study the root cause failure.ODI will monitor FCA?s analysis to determine if any further field action is warranted.Based on the actions taken by FCA to recall the MY 2007-2010 Jeep Wrangler vehicles and the MY 2008-2016 right hand drive Wrangler vehicles, this investigation is closed.FCA has also agreed to conduct a warranty extension and further evaluation of the MY 2011-2016 Wrangler.At the time of FCA's field data submission in PE 15-025 (September 2015), ODI was aware of a total of 416 MY 2007-2010 and 23 MY 2011-2012 VOQs relevant to this issue.In addition, there have been an additional 90 and 16 VOQs (respectively) received since the recall announcement (i.e., thru May 2016).The reports noted above can be viewed at SaferCar.gov under the reference (ODI) numbers cited on the attached listing.

Closed preliminary evaluation · opened June 19, 2015 · closed December 7, 2015

the air bags

In it's response to ODI's PE15-025 Information Request letter, FCA identified 1,703 consumer complaints, field reports and legal claims responsive to the subject defect condition on the subject Wrangler vehicles.Six of these reports alleged an air bag non-deployment in a crash in which either the air bag warning light was allegedly on or came on afterward the crash, one of which also alleged injuries as a result of the non-deployment.FCA also provided data on other make, model and model year vehicles using the same clockspring.Additionally FCA provided 16,955 warranty claims related to the replacement of the air bag clockspring wiring assembly.It should be noted that FCA initiated an Extended Warranty Program on the left hand drive MY 2007 Wrangler in late calendar year 2011.6,777 of these claims are from the MY 2007 left hand drive Wrangler.FCA advises that some of the warranty claims involved clockspring failures that would not affect the air bag operation, for example due to noise, cruise control and/or radio operation issues.Many of these claims involved newer model year subject vehicles.FCA also noted that Wrangler's removable roof and door configuration may make it more susceptible to outdoor water/moisture and dust ingress.ODI investigated the right hand drive Wrangler in calender year 2011 for a similar clockspring issue under PE11-019.That investigation lead to NHTSA Safety Recall 11V258 on right hand drive model year (MY) 2008-2012 Wranglers.FCA redesigned the remedy clockspring to improve its durability and environmental protection and revised the design of the steering wheel to column shroud.Base on the data reviewed, this Preliminary Analysis (PE) is being upgraded to an Engineering Analysis (EA).The reports cited above are listed in the public investigative file available at SaferCar.gov under this investigation ID.

Closed defect petition · opened September 25, 2014 · closed July 24, 2015

the electrical system

In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den

Closed preliminary evaluation · opened March 28, 2012 · closed August 7, 2012 · led to recall 12V216000

the engine and its cooling, the power train

In a letter dated May 15, 2012, the Chrysler Group LLC (Chrysler) submitted a Defect Information Report to NHTSA identifying a safety defect regarding fires originating between the transmission skid plate and the exhaust catalyst in approximately 65,246 model year (MY) 2010 Jeep Wrangler 4x4 vehicles with automatic transmissions (NHTSA Recall 12V-216).According to Chrysler, changes to the exhaust system for MY 2010 resulted in reduced clearances between the exhaust catalyst and the skid plate.If debris collects in the area of the skid plate and is not removed, there is an increased potential for underbody debris fires.ODI's analysis of skid plate area fires in the MY 2010 Wrangler vehicles with automatic transmissions found that the rate increased significantly from approximately 1.7 fires per 100,000 vehicle years in the MY 2007 through 2009 vehicles with the prior exhaust design to approximately 14.8 fires per 100,000 vehicle years in MY 2010 vehicles, a nearly 800 percent increase.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and Chrysler's consumer complaint data submitted to ODI, 35 unique reports were identified by Chrysler alleging fire in subject vehicles with origins near the engine compartment or in the underbody area directly beneath and to the rear of the engine compartment.Chrysler's assessments of the 35 reports of fire were categorized by likely causes.Eleven of the fires were determined to be caused by skid plate debris accumulation and 4 additional fires were found to have originated in the area of the skid plate, but debris ignition could not be confirmed.An additional skid plate debris fire was reported to ODI after the recall announcement, bringing the total known fire count to 36, including 12 caused by skid plate debris and 4 originating in the skid plate area from unknown causes.Chrysler identified a design change to the exhaust system in MY 2010 that increased the possibility of debris contact with an exhaust catalyst.Beginning in MY 2011, the skid plate was replaced with a skid bar for weight reduction purposes.The skid bar having a much smaller surface area than the skid plate reduces the potential for debris entrapment.The recall remedy for recall 12V-216 will involve replacement of the skid plate with the skid bar.As background, the MY 2010 subject vehicles are a part of the JK generation of Jeep Wrangler vehicles that began production in MY 2007.Chrysler conducted a prior recall (09V-436) of MY 2007 and 2008 Jeep Wranglers for a defect involving overheated transmission fluid expulsion that could contact the exhaust and cause an engine compartment fire.The recall remedy was to add audible (chime) and visual warnings (hot oil message in the instrument cluster) to alert the driver that the vehicle was being operated with elevated transmission fluid temperatures.Chrysler enhanced the audible warning with a service campaign (J31) for MY 2009 and a portion of the subject MY 2010 vehicles.Transmission fluid expulsion has not been identified as the cause of any of the 36 fire incidents in the subject vehicles. No indications of a common causal pattern were evident in the remaining 20 fire incidents in the subject vehicles.Six (6) of the incidents appear to be related to improper wiring of various added aftermarket equipment, 2 appear to be related to improper oil change, 1 was related to a damaged transfer case, 1 was related to an electrical short circuit and the remaining 10 were of unknown origin.Accordingly, this Preliminary Evaluation is closed.The ODI reports cited above can be reviewed at www-odi.

My vehicle has experienced a complete failure of the ABS Control Module. A dealer diagnosis confirmed internal module failure. The symptoms are: - All ABS system warning lights illuminated (ABS, traction control, brake, sway bar) - Odometer and speedometer stop working while driving - All brake lights remain on continuously - Vehicle exhibits erratic shifting / rough braking This is a documented safety defect affecting many Chrysler/Dodge/Jeep owners where the dealer confirms the ABS module is defective but cannot repair due to the part being on national backorder with no ETA. I am being told the part is backordered indefinitely. I am left driving an unsafe vehicle with no functioning ABS, …

NHTSA complaint 11757235, quoted in part. Filed by an owner and not verified by NHTSA or by us.

Failure to replace airbags

NHTSA complaint 11751743. Filed by an owner and not verified by NHTSA or by us.

Most of the dash lights are on scan code U1412. Says traction control not working, ABS not working, speedometer not working, and airbags not working. The Power Control Module (PCM) needs replaced. A known issue with the Jeep Wrangler JKs. No one stocks the parts and used ones are way over priced. How can Jeep not have to replace it or at least stock a replacement part that has the issues resolved?

NHTSA complaint 11748027. Filed by an owner and not verified by NHTSA or by us.

Abs module failed the company no longer makes the chips to repair this module

NHTSA complaint 11744768. Filed by an owner and not verified by NHTSA or by us.

El vehículo fue llevado para un recall del airbag clock spring todo estaba bien hasta ahora que en el mes de marzo 2026 el volante comenzó hacer ruido, la bocina a penas funciona, el votante se siente suelto y la luz del airbag se encendió.El vehículo no ha sido inspeccionado ya que llame al no tener garantía y no tener recall no dan opciones para reparo por recall en una segunda ocasión Pone en riesgo mi seguridad ya que puede expulsar el airbag y ocasionarme un accidente o lesión física. Está situación puede ocasionar accidentes muy graves.

NHTSA complaint 11726076. Filed by an owner and not verified by NHTSA or by us.