2014 BMW 320I

The defect

BMW of North America, LLC (BMW) is recalling certain 2014 4 Series Coupe (428i, 428i xDrive, 435i, 435i xDrive), 3 Series Sedan (320i, 320i xDrive, 328i, 328i xDrive, 335i, 335i xDrive), and 2014-2015 2 Series Coupe (228i, 228i xDrive, M235i, M235i xDrive) vehicles. The head air bag inflator may fail at the weld joint, which can cause gas to leak from the inflator or result in an inflator rupture.

The risk

An inflator that ruptures may cause sharp metal fragments to enter or exit the vehicle, increasing the risk of injury. Additionally, an inflator that leaks gas may only partially inflate during a crash, increasing the risk of injury.

The remedy

Dealers will replace the head air bags, free of charge. Owner notification letters were mailed February 12, 2026. Owners may contact BMW customer service at 1-800-525-7417.

BMW of North America, LLC · up to 851 vehicles across all model years covered

The defect

BMW of North America, LLC (BMW) is recalling certain 2015 6 Series Gran Coupe, 2014 5 Series Gran Turismo, 2014 5 Series Sedan, 2015 6 Series Convertible, 2015 6 Series Coupe, 2014 X5, 2013-2014 X3, 2014-2015 3 Series Sedan, 2014 4 Series Coupe, 2014 4 Series Convertible, 2014 3 Series Gran Turismo, and 2015 4 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. The driver's air bag inflator may explode during deployment, due to a manufacturing defect.

The risk

An inflator explosion may result in sharp metal fragments striking the driver or other occupants, increasing the risk of injury or death.

The remedy

The driver's front air bag will be replaced, free of charge. Owner notification letters were mailed September 6, 2024. Owners may contact BMW customer service at 1-800-525-7417.

BMW of North America, LLC · up to 1,145 vehicles across all model years covered

The defect

BMW of North America, LLC (BMW) is recalling certain 2014-2015 2 Series Coupe (228i, 228i xDrive, M235i), 3 Series Sedan (320i, 320i xDrive, 328i, 328i xDrive, 335i, 335i xDrive, M3, 328d, 328d xDrive), 4 Series Coupe (428i, 428i xDrive, 435i, 435i xDrive, M4), and 2015 4 Series Gran Coupe (428i, 428i xDrive, 435i, 435i xDrive) vehicles. The head air bag inflator may fail at the weld joint, which can cause gas to leak from the inflator or result in an inflator rupture.

The risk

An inflator that ruptures may cause sharp metal fragments to enter or exit the vehicle, increasing the risk of injury. Additionally, an inflator that leaks gas may only partially inflate during a crash, increasing the risk of injury.

The remedy

Dealers will replace the head air bags, free of charge. Owner notification letters were mailed November 4, 2024. Owners may contact BMW customer service at 1-800-525-7417.

BMW of North America, LLC · up to 5,761 vehicles across all model years covered

The defect

BMW North America, LLC (BMW) is recalling certain model year 2012-2015 320i, 320xi, 328i, 328xi, 335i, 335xi, and ActiveHybrid3 vehicles manufactured October 20, 2011, to June 22, 2015, 2014-2015 328xi Sports Wagon vehicles manufactured March 21, 2013, to March 17, 2015, 2014-2015 328d, 328xd vehicles manufactured June 28, 2013, to April 21, 2015, and 2014-2015 328xd Sports Wagon vehicles manufactured July 5, 2013, to April 21, 2015. The affected vehicles may have been programmed with new software that inadvertently makes the front side marker lights inoperative in conjunction with the parking lights or the headlights. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."

The risk

If the side marker lights do not illuminate, the vehicle may be less visible at night, increasing the risk of a crash.

The remedy

BMW will notify owners, and dealers will upload revised software to correct the issue, free of charge. The recall began on October 7, 2015. Owners may contact BMW customer service at 1-800-525-7417 or by email at CustomerRelations@bmwusa.com.

BMW of North America, LLC · up to 7,727 vehicles across all model years covered

The defect

BMW of North America LLC (BMW) is recalling certain model year 2014 228i Coupe, M235i Coupe, 320i, 320xi, 328i, 328xi, 335i, 335xi, ActiveHybrid 3, 328xi Sports Wagon, 428i Coupe, 428xi Coupe, 435i Coupe, 435xi Coupe, 428i Convertible, 428xi Convertible, 435i Convertible, 328xi Gran Turismo, 335xi Gran Turismo, and 2015 428i Gran Coupe, 428xi Gran Coupe, and 435i Gran Coupe vehicles. Improper nickel plating of components within the fuel pump may result in the fuel pump failing.

The risk

If the fuel pump fails, the vehicle may stall without warning, increasing the risk of a crash.

The remedy

BMW will notify owners, and dealers will replace the fuel pump, free of charge. Owners were mailed interim notices on May 28, 2015. The recall began on July 6, 2015. Owners may contact BMW customer service at 1-800-525-7417.

BMW of North America, LLC · up to 18,054 vehicles across all model years covered

The defect

BMW of North America LLC (BMW) is recalling certain model year 2014 BMW 328i xDrive Sports Wagon, 2012-2014 BMW 320i Sedan, 328i Sedan, 320i xDrive Sedan, 328i xDrive Sedan, 2012-2013 BMW 528i Sedan, 528i xDrive Sedan, 2013-2014 BMW X1 sDrive28i, X1 xDrive28i Sports Activity Vehicle, 2013-2014 BMW X3 xDrive28i Sports Activity Vehicle, 2012-2014 BMW Z4 sDrive28i Roadster, and 2014 BMW 428i Coupe, and 428i xDrive Coupe. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail. Note: This recall is an expansion of recall 13V-454.

The risk

A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.

The remedy

BMW will notify owners, and dealers will install a locking ring in the camshaft to retain the camshaft seal disk in the proper location, free of charge. The recall began on December 2, 2014. Owners may contact BMW customer service at 1-800-525-7417.

BMW of North America, LLC · up to 8,988 vehicles across all model years covered

The defect

BMW of North America LLC (BMW) is recalling certain model year 2012-2014 320i, 328i, 320i xDrive, and 328i xDrive sedans; model year 2014 328i xDrive Sports Wagons; model year 2012-2013 528i and 528i xDrive sedans, model year 2013-2014 X1 sDrive28i and X1 xDrive28i vehicles and model year 2012-2014 Z4 sDrive28i roadsters. Due to insufficient lubrication, the vacuum pump that supplies brake power assistance may fail.

The risk

A failure of the brake vacuum pump results in a reduction in braking power that could increase the risk of a crash.

The remedy

BMW will notify owners, and dealers will modify the vehicles to prevent insufficient vacuum pump lubrication, free of charge. The safety recall began on January 31, 2014. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.

BMW of North America, LLC · up to 76,191 vehicles across all model years covered

Still open engineering analysis · opened September 17, 2021

the air bags

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Closed preliminary evaluation · opened September 6, 2013 · closed October 25, 2013 · led to recall 13V454000

the hydraulic brakes

In a letter dated September 26, 2013, BMW Group submitted a safety recall notice to NHTSA identifying a defect condition in the vacuum pump oil supply that may result in loss of power assist braking in 76,191 model year (MY) 2012 through 2014 BMW 3-Series, 5-Series, X1 SAV, X3 SAV, and Z4 vehicles equipped with 4-cylinder engines (NHTSA Recall 13V-454).According to BMW, movement of the seal disk within the camshaft may result in blocking of the oil supply to the vacuum pump, resulting in improper pump operation and loss of power assist braking.On July 11, 2013, BMW initiated a change to the camshaft geometry that prevented the seal disk from blocking the oil port.BMW has not received any braking complaints related to loss of power assist after the design change was implemented in production.The owners of all affected vehicles will be contacted by mail and asked to take their vehicle to a BMW dealer who will install a locking ring into the camshaft to keep the seal disk in its proper location.BMW expects to begin dealer and owner notification in November 2013 and complete dealer and owner notification in December when the remedy is expected to be available.Based on the actions taken by BMW, this investigation is closed.

I was driving on a on a busy interstate after work and out of nowhere I get the Temperature warning and start losing power. This is Dangerous! I am submitting this complaint to report a safety‑related defect involving the electric water pump on my 2014 BMW 320i. This issue is widely documented among BMW owners, and several 3‑Series models from the same production years have been included in recalls or service bulletins for premature water pump failure. However, the 2014 BMW 320i (F30 chassis, N20/N26 engine) is not included, despite experiencing the same failure pattern. In my case, the water pump failed without warning. During the coolant bleeding process, there was no circulation or pump …

NHTSA complaint 11722945, quoted in part. Filed by an owner and not verified by NHTSA or by us.

towed · 95,000 miles

The contact owns a 2014 BMW 320I. The contact stated that after pulling into a parking lot at approximately 10 MPH and shifting the vehicle into park(P), the message that the engine was overheating was displayed on the instrument panel. After waiting a while for the engine to cool down the contact restarted the vehicle and exited the parking lot. The contact stated that the vehicle began hesitating and sputtering as if the vehicle was going to stall. The contact pulled into another nearby parking lot to park and turn off the vehicle. The vehicle was towed to a certified mechanic and the contact was informed that the water pump had failed and needed to be replaced. The vehicle had not been …

NHTSA complaint 11609883, quoted in part. Filed by an owner and not verified by NHTSA or by us.

I own a 2014 BMW 320IX and first time today, August 20th the Engine Overheat message came on my dashboard and then started to go idle and appear that it was about to die. Upon letting the car sit for a few hours to cool off, within a quarter of a mile of driving the car again the light came up and started to idle and felt like it was going to die again. Twice today, I was left stranded in parking lot and to call a tow truck to have it towed to an independent auto mechanic that fixes BMW. This evening I noticed a recall for 2012 - 2014 BMW 328 and 328IX. This is also an issue with the 2014 BMW 320IX models too. I need this recall to also include the 320IX model. How can this be updated and …

NHTSA complaint 11609851, quoted in part. Filed by an owner and not verified by NHTSA or by us.

The electrical water pump that was just recalled on over 720,000 bmws is the same water pump on the 320is. My vehicle as of now has had issues with the pump completely going out causing high temperature issues with the motor while driving.

NHTSA complaint 11609854. Filed by an owner and not verified by NHTSA or by us.

40,000 miles

The contact owns a 2014 BMW 320I. The contact stated while pulling on the seat belt to fasten the seat belt, the seat belt would not extend. The vehicle was not diagnosed. The vehicle was not repaired. The manufacturer was not contacted. The failure mileage was 40,000.

NHTSA complaint 11519480. Filed by an owner and not verified by NHTSA or by us.

Timing chain malfunction and power train malfunction

NHTSA complaint 11500593. Filed by an owner and not verified by NHTSA or by us.